Axon POS System A70 Especificaciones

-10- 2-2. Product Outline (Note: Labels may differ according to model/region) [Control Panel] ERROR (LED) : Blinks red when co

-11- [Connecting Cables] 1. Ensure that both the printer and host terminal are switched off. 2. Connect the power cable b

-12- [Installing Paper Roll] 1. Push down on the level to the left side of printer to open the cover. 2. Switch off the power. 3

-13- 2-3. Basic Installation OPOS Driver The UNIPOS driver for OPOS driver system (based on Windows XP) is provided. Alternatively, you can download

-14- ● Installation 1. Download EasySet OPOS driver file and install. 2. Complete the installation of OPOS driver. 3. File is located at: [Start] –

-15- Select „Device Name‟ and „Device Type‟, then click “Add”. [„Select Device Type‟: Serial, parallel or USB] Select newly added p

-16- Enter port details in the Printer Settings page and press [OK] to complete the setup. ※ When setting up the ‘Cash Drawer’, please use

-17- 2-4. Port settings 1. Physical USB port settings ● Installation 1. Download the A70 printer driver file relevant to your operating system (

-18- After installation is complete, connect the A70 USB cable. ※ When connecting the A7O printer via USB, Physical/Actual USB must always be

-19- Go to: Start -> Printers and faxes ->EASYSET PBP_A7 -> Printer settings After checking the printer settings, the test print should be

-2- CONTENTS Chapter 1. Introduction Chapter 3. Product Settings 1-1 Warranty 3 3-1. Specifi

-20- 2. Virtual COM (RS232 Serial Emulation) port settings ● Installation 1. Visit and download the file from „Others‟ -> „Virtual Serial Dri

-21- Once the A70 Virtual Serial Driver has been installed, go to: Device manager -> Ports, and check that the A70 Printer Virtual Serial Port Fo

-22- Thermal Receipt Printer Chapter 3. Product Settings 3-1. Specifications · Versatile & adaptable applications · Robust and cost effect

-23- 3-2. Printer Setup Printer Firmware ● Installation 1. Insert CD or download EasySet Print Firmware driver www.axoncomputer.it 2. Install P

-24- NVImage The „NV Image Tool‟ program allows the user to add images to the printed receipt. The program is compatible with ECP-500/ECP-500A, F100

-25- ① Preview of image ② Open file ③ Delete image ④ Uploads selected image to printer ⑤ Exit Step 1. Click ② [File Open] . Step 2. Con

-26- ① Interface Selects interface type ② Serial Port Setting Choose serial port settings ③ Upload Uploads and applies the selected i

-27- 3-3. Printer settings The printer properties (baudrate, density etc.) can be changed from the printer’s ‘Setting mode’. To enter „Setting mode‟:

-28- 4. The printer‟s „Self-test‟ will begin. 5. Information about the printer‟s current state will be printed. 6. After 5 seconds without releasing

-29- * The following table shows the available options for each property in „Setting mode‟. No Function Button Count Setting Default 1 Step by Step S

-3- Thermal Receipt Printer Chapter 1. Introduction 1-1. Warranty We guarantee our POS terminal product and its parts against defects in materi

-30- 8 Code Page ※ Please refer to the table on the right. 9 USB Mode 1 Serial Emulation Actual USB 2 Actual USB 3 Ethernet to USB For example, To

-31- * To select the desired language, press the FEED button the corresponding number of times. PAGE 1 Button Count CODE PAGE LANGUAGE 1 Next code pa

-32- PAGE 3 Button Count CODE PAGE LANGUAGE 1 Next code page 2 CP-737 Greek 3 CP-775 Baltic 4 CP-855 Cyrillic 5 CP-857 Turkish 6 CP-861 Icelandic

-33- Thermal Receipt Printer Chapter 4. Maintenance This section shows the user the correct way to remove and replace the printer cutter, mother

-34- [Printer cutter replacement] 1. Open the printer cover and remove the 2 screws from the cutter (as shown above). 2. Remove the cutter. 3. Repl

-35- [Motherboard replacement] 1. Remove the power cable from the unit and open the cover by pressing down on the level to the left of the printer.

-36- 3. Remove the 2 flat-headed screws from the locations shown above. 4. Remove the 2 screws from the underside of the printer (as shown above).

-37- 5. Ensuring that the cover is open, pull vertically upwards to separate the top casing from the bottom casing. 6. The side of the printer

-38- 7. Push down and forward on the front lid to completely separate the two parts. 8. When separating the top case from the bottom case, take car

-39- 9. Remove the 3 screws from the face of the motherboard and separate from the main unit. 10. Replace the motherboard and reassemble the unit u

-4- 1-2. Copyright This publication, including all photographs, illustrations and software, is protected under international copyright law with all r

-40- [Printer mechanism replacement] 1. Remove the motherboard as shown in the previous section. 2. Remove the 2 screws from the location behind th

-41- 4. Remove the top casing from the motherboard panel. 5. Remove the 6 black circular M2.0 screws from the location shown above. 6. Remove the p

-42- Thermal Receipt Printer Chapter 5. Printer Operation 5-1. Printer Self-test 1. Make sure the paper roll is installed correctly. 2. While ho

-43- 5-2 Paper Jam Correction 1. In the event of a paper-jam, immediately stop printing. 2. Open the top cover by pressing down on the „COVER OPEN B

-44- 5.3 Printer Specifications Printing Method Direct thermal Printing Speed 170mm/sec Dot Density (DPI) 203.2 Dot Pitch (mm) 0.125*0.125 Effective

-45- Power 24 VDC / 2.5A Data Buffer 4 Kbyte Cutting Life 700,000 cuts Cutting method Partial Cut / Full Cut Temperature Operation 0 ~ 40℃ Storage -2

-5- 1-4. Liability Limitation ● Installation and maintenance We recommend that you inquire about product installation, maintenance and repair servi

-6- ● Cleaning procedure Cleaning with chemical based products (in particular those containing benzyl or chemical thinning agents) can damage the ex

-7- 1-5. Installation Recommendations 1. Avoid installing during thunderstorms. (Possibility of dangerous exposure to electricity.) 2. Install away f

-8- Thermal Receipt Printer Chapter 2. Product Overview 2-1. Inside Your Package Included in the package: Printer, power cable, interface cable,

-9- [Package Contents]